HS range · leisure vessels
New

HullSonic HS400

Four transducers, all four channels working

Ultrasonic antifouling for larger leisure vessels: the four-channel HS control module with four transducers.

A$3,020.00 incl. GST

Free express delivery to Australia. Dispatched from the Gold Coast.

Plan my layout

3-year warranty, extended while a HullSonic dashboard plan is active · Australian made

Specifications ↓
4
Transducers
200 W
Acoustic output, 4 × 50 W
3 yr
Warranty
HS control module

Every channel live. 200W of ultrasonic protection for vessels to about 49ft/15m.

The HS400 is the complete HullSonic recreational system — four transducers, four independently calibrated channels, and coverage for the running surfaces that matter.

Four transducers, four independent channels

Four channels means four separately calibrated acoustic zones, not one signal split four ways. Each transducer is driven by its own channel, auto-tuning across the 19–80kHz band to the hull section it’s bonded to. A transducer on a thin topside panel and one on a heavy keel section behave completely differently — the HS400 treats them as different problems, because they are.

That matters most on the areas owners actually lose to fouling: the turn of the bilge, the keel root, the area ahead of the running gear, and sea chests or strainer boxes.

45–55W per channel. 200W total.

Each channel is user-adjustable 45–55W and ships at 50W, for 200W of ultrasonic acoustic energy across the installation. You can bias power toward the channels doing the hardest work and back off where fouling pressure is lower — a level of control that matters on a boat living somewhere warm.

ECO, STANDARD and BOOST

  • ECO — for solar, wind and limited shore power. Lower draw, continuous protection.
  • STANDARD — the everyday setting.
  • BOOST — maximum output for peak fouling season or an extended lay-up.

Programmable sleep stands the system down for 4–8 hours and resumes automatically.

Colour display and WiFi

Live per-channel drive power, calibration state and fault reporting on a full-colour display — with four channels running, being able to see at a glance which one has a problem is the difference between a five-minute check and an afternoon with a multimeter. WiFi handles setup, diagnostics and over-the-air firmware updates.

12–24VDC, auto-sensing

One unit for both bus voltages. No configuration, no variants.

Each transducer has 10 m (32 ft) of cable attached. On a larger boat a cable may need extending to reach its transducer: contact us for advice. Bigger boats combine systems, and the layout planner works out how many transducers yours needs.

Hardware

A closer look

Transducer layout guide by boat length
Transducer layout guide by boat length
HS-T50 transducer
HS-T50 transducer
HS-T50 transducer with its cable
HS-T50 transducer with its cable
HS wiring: four transducers, supply and fuse
HS wiring: four transducers, supply and fuse
Features

What's in the box

01
Control module

HullSonic HS400, all 4 channels active

02
4 × HS-T50 transducers

Each with 10 m (32 ft) of silicone rubber cable attached

03
4 × mounting rings

Bonded inside the hull; each transducer screws into its ring

04
Gasket material

A tube of Loctite 515 for the transducer faces

05
Power cable

5 m (16 ft) silicone rubber battery cable, already attached to the module

06
Installation kit

JB Weld epoxy adhesive and mixer

07
Fuses

In-line fuse and a spare fuse kit

08
Manual

Full-colour installation and operation manual

Specifications

HullSonic HS400 at a glance

Controller 4-channel hardware
Transducers 4 × HS-T50
Output per channel 45–55 W, 50 W default
Frequency 19–80 kHz, auto-calibrating per channel
Supply 12–24 V DC, auto-sensing
Transducer cable 4 x 10 m (32 ft) silicone rubber
Ingress protection IP67 control module, IP68 transducers
Display Colour display
Power modes ECO / STANDARD / BOOST
Connectivity WiFi, over-the-air firmware updates
Weight 4.5 kg
Warranty 3 years return-to-base, extended while a HullSonic dashboard plan is active
Certification FCC · CE · RCM · RoHS (control module)
Owners

Clean hulls, in their words

Testimony   CleanAHull Ultrasonic Antifouling Success Aquila 002

Six months in Sarasota, hull never cleaned.

“My 44-foot Aquila power cat has now been in the hot, fertile, Sarasota water for approximately six months. In that time, I have not cleaned the hull once.”

Rick R. · Aquila 44 power catamaran · Sarasota, Florida

Nine months, no bottom cleaning.

“I have not had to clean the bottom once in the nine months since it was installed. What slime builds up on the bottom is dead and washes right off when the boat starts moving.”

Michael C. · Cruisers 5000 Sedan Sport · Siesta Key, Florida · fitted 2014

More from owners →

See where the transducers go on your boat

Pick your boat, drive and what you want protected. The layout planner draws the transducer positions on your hull and puts the matching system in your cart.

Plan my layout
Plan my layout