Accessories and spares

Upgrade kits and spares

Everything to take a two-transducer system to three or four, and the spares to re-site or replace a transducer.

The upgrade path

Every two-transducer system is ready for four

The HS200 and the MAX2 are not cut-down systems. Each has the same four-channel control module as the HS400 and the MAX4, supplied with two transducers. Channels 3 and 4 are already inside the module, switched off.

An upgrade kit is the transducers for those channels, each with its cable and mounting ring: two in the upgrade kit, one in the single kit. Fit them, switch the channels on, and you have a three- or four-transducer system. There is no new module to buy and no change to the power feed.

Two channels working, two ready
12341234
  1. Control module: every HS200 and MAX2 has the full four-channel module, the same one as the HS400 and MAX4.
  2. Channels 1 and 2 drive the two transducers supplied with the system.
  3. The upgrade kit: two more transducers with their cables and mounting rings. The single kit has one.
  4. Channels 3 and 4 are already in the module, switched off. Switch them on from the system menu or in the HullSonic dashboard.

Kits and spares

One more transducer, or two

Choose the kit for your controller. The two-transducer kit uses both spare channels and costs less than two single kits. The single kit adds one transducer and leaves a channel free for later; it is also the replacement if a transducer is damaged.

For HS200 · two transducers

HS transducer upgrade kit

Two HS-T50 transducers, each with 10 m of cable and a mounting ring, to enable channels 3 and 4. A$1,415.00 incl. GST

View

For HS200 · one transducer

HS single transducer kit

One HS-T50 transducer with 10 m of cable and a mounting ring, to enable one more channel. A$780.00 incl. GST

View

For MAX2 · two transducers

MAX transducer upgrade kit

Two HS-T60 transducers, each with 10 m of cable and a mounting ring, to enable channels 3 and 4. A$1,415.00 incl. GST

View

For MAX2 · one transducer

MAX single transducer kit

One HS-T60 transducer with 10 m of cable and a mounting ring, to enable one more channel. A$780.00 incl. GST

View

Spare

Transducer mounting ring

A spare bonded ring for HS-T50 and HS-T60 transducers, for re-siting a transducer. A$48.00 incl. GST

View

Buying four transducers up front always costs less than two plus an upgrade kit later. The kits are there for when your boat or your mooring changes. The HS400 and MAX4 already use all four channels.

Fitting the kit

Three steps, on the module you already have

01

Plan the new positions

Use the layout planner to see where four transducers go on your boat, then check each new site inside the hull: flat, accessible, clear of stringers, tanks and bulkheads.

02

Bond, fit and connect

Clean and key each site and bond a mounting ring to the inside of the hull. Fit each transducer and run its cable to channel 3 or 4 on the control module.

03

Switch the channels on

Enable each new channel from the module’s system menu or in the HullSonic dashboard. It calibrates itself to its section of hull.

Owners usually add the kit when they move the system to a larger boat, want to protect more than the hull, or keep the boat on a mooring with heavy fouling. Installation in outline.

Example: a 12 m cruiser with four transducers, their zones overlapping along the hull.

Not sure how many transducers?

Pick your boat, drive and what you want protected. The layout planner draws the transducer positions on your hull and puts the matching HS or MAX system in your cart.

Plan my layout