Support

Frequently asked questions

The questions owners ask most, answered by the engineering team. Something missing? Contact us.

Suitability

Will it work on my boat?

Will HullSonic work on my boat?

HullSonic works on GRP, aluminium and steel hulls, including catamarans. It is not suitable for timber or ferro-cement hulls. Foam- or balsa-cored hulls need a small modification at each transducer site.

What size boat does each system cover?

The u003ca href=u0022/planner/u0022u003elayout planneru003c/au003e sizes the system for your hull. As a guide, an HS200 suits most boats to about 10 m and an HS400 to about 15 m. MAX2 and MAX4 cover the same sizes with vessel-integration features, and larger yachts run several controllers. For ships, ferries and port infrastructure, see our commercial brand u003ca href=u0022https://envsonic.com/?utm_source=hullsonicu0026utm_medium=faqu0022u003eENVSonicu003c/au003e.

My hull is foam- or balsa-cored. Does it work?

Yes, with some preparation at each transducer site. The ultrasound has to go straight into the solid outer skin, so the inner skin and core are cut away over the mounting ring’s footprint, the ring is bonded to the outer skin, and the cut edges are glassed over to seal the core. A professional installer can do this for you.

Why doesn’t it work on timber hulls?

Ultrasound needs a dense, continuous hull to travel through. Timber is relatively soft and planked hulls are full of joins, so the energy stays in a small area around the transducer. The same goes for ferro-cement. GRP, aluminium and steel all carry it well.

Is there a maximum hull thickness?

Solid GRP, aluminium and steel hulls of normal boat-building thickness are fine. Very thick or heavily built hulls may need extra transducers. u003ca href=u0022/contact/u0022u003eSend usu003c/au003e the laminate thickness at the transducer positions and we’ll check.

How many transducers do I need?

Each transducer protects a zone roughly 4.5–5 m across, and the zones should overlap along the hull. The layout planner works it out for your boat.

Where do the transducers go?

Inside the hull, below the waterline. One goes as close as it can to the shaft and propeller, and the others are spread along the hull so their zones overlap. How much protection the running gear gets depends on the boat. The u003ca href=u0022/planner/u0022u003elayout planneru003c/au003e marks the positions for your boat.

What about commercial vessels?

Ships, tugs, ferries, sea chests, raw-water cooling and port infrastructure are handled by our commercial brand u003ca href=u0022https://envsonic.com/?utm_source=hullsonicu0026utm_medium=faqu0022u003eENVSonicu003c/au003e: same engineering team, engineered and quoted per project.

Results

What to expect

Will it remove existing growth?

No. HullSonic prevents new growth from settling. Fit it on a clean hull, ideally after fresh antifouling, and it keeps the hull cleaner for longer.

How soon will I see results?

Protection starts the moment the system is switched on: on a clean hull, new growth doesn’t take hold. Soft growth that hadn’t fully attached usually starts coming away within a few weeks, mostly when the boat is underway. Barnacle shells that were already there stay until they’re cleaned off.

Do I still need antifouling paint?

We recommend keeping antifouling paint. HullSonic works with it: the paint lasts longer and the time between haul-outs and diver cleans stretches out. Paint also keeps water staining down, which HullSonic doesn’t prevent.

How does it compare with copper antifouling paint?

Copper paint wears away by design, releases biocide into the water and needs renewing every year or few. HullSonic releases nothing into the water and works continuously. Most owners use both: the paint lasts longer and haul-outs come around less often.

Will I use less fuel?

A clean hull has less drag than a fouled one, so a boat that stays clean holds its speed and uses less fuel than it would fouled. How much you save depends on how fast your hull fouls without protection. The u003ca href=u0022/#savingsu0022u003eowner savings calculatoru003c/au003e lets you put in your own figures.

How long will the system last?

It is built to run continuously for years: a sealed controller and potted transducers (on MAX, IP67 and IP68), made and tested on the Gold Coast. Every system has a three-year warranty, extended for as long as a dashboard plan is active.

Running it

Power, noise and safety

Does it need to run all the time?

Yes, protection depends on the system running continuously. ECO mode reduces power draw for boats on solar, wind or limited shore power.

How much power does it use?

Very little on average: about 3–4 W per transducer. Each channel works in short bursts at up to its rated power (50 W on HS, 60 W on MAX), which is why the average stays low. ECO mode reduces it further.

Will it flatten my batteries?

No. HS and MAX systems run on 12 or 24 V from your house bank, like any other equipment (older HS200 and HS400 units are 12 V only; MAX, as CleanAHull, has always taken both). The controller watches battery voltage: if it drops too far, it raises an alarm and stops output to protect the bank.

My boat is on a swing mooring. Will it work, and can it run on solar?

Yes. Shore power isn’t needed, only a battery that stays charged. A modest solar panel or wind generator usually covers the average draw, and ECO mode helps on small systems. u003ca href=u0022/contact/u0022u003eTell usu003c/au003e your boat and power setup and we’ll help size it.

Can I hear it?

Not in normal use: it works above the range of human hearing. Right next to a transducer you may hear a faint clicking, which is a handy sign that it is running.

Will it interfere with my other electronics?

It is designed not to. It runs on its own circuit and the transducers are galvanically isolated from the rest of the boat. If you ever notice anything unusual on a sounder or other equipment, u003ca href=u0022/contact/u0022u003econtact usu003c/au003e and we’ll help.

Can it cause electrolysis?

No. The transducers are galvanically isolated from the rest of the boat and driven with alternating current.

Will my anodes wear faster?

No. No current goes into the water from the transducers, so anode wear doesn’t change.

Can ultrasound damage my hull?

No. The energy is low and acts at the hull surface on microscopic organisms. It doesn’t harm GRP, aluminium or steel, or the equipment on board.

Is it harmful to marine life, pets or people?

No. The system releases nothing into the water: no biocides and no metals. It works at the hull surface on the microscopic larvae and algae that start fouling, not on fish, marine mammals, pets or people.

Will it tell me if a transducer stops working?

Yes. The controller checks every channel and shows a fault on its display. MAX also has an alarm output you can connect to your vessel’s alarm or monitoring system, and systems on a dashboard plan can alert you remotely.

Does it need maintenance?

No routine maintenance. Every so often, check the cables for chafe, make sure each transducer is tight in its ring and glance at the controller’s display. Listening for the faint click at each transducer is a quick check that it is working.

Installing

Fitting a system

How long does installation take?

A few hours of work plus curing time for the bonding resin. Most owners with basic 12 V skills fit their own system in a day. See u003ca href=u0022/install/u0022u003einstallationu003c/au003e for the steps and videos.

Can I install it myself?

Yes. Each system comes with the mounting rings, bonding resin, cables and instructions, and the wiring is plug-in. If you’d rather not, a u003ca href=u0022/dealers/u0022u003elocal installeru003c/au003e can fit it.

Do I need to drill holes in my hull?

No. The transducers fit inside the hull: each screws into a mounting ring bonded to the inside of the hull, so there are no through-hull fittings.

Can it be installed with the boat in the water?

Yes. Everything is fitted from inside, so the boat doesn’t need to come out for the installation itself. Start with a clean hull, though: if it is fouled, have it cleaned by a diver or at a haul-out first, because HullSonic stops new growth rather than removing what is already there.

Can I move the system to a new boat?

Yes. The controller, transducers and cables move across. The mounting rings are bonded permanently, so fit u003ca href=u0022/systems/accessories/transducer-mounting-ring/u0022u003enew ringsu003c/au003e on the new hull rather than trying to remove the old ones.

Can I start with two transducers and add more later?

Yes. HS200 and MAX2 have all four channels built in; add the transducer upgrade kit and switch channels 3 and 4 on from the module menu or the dashboard.

Buying

Range, warranty and delivery

What is the difference between HS and MAX?

Both use the same 4-channel controller. HS runs 50 W channels for leisure vessels; MAX (formerly CleanAHull) runs 60 W channels with channel grouping and vessel integration for superyachts and prestige vessels.

How is it different from older analogue systems?

Older analogue units drove their transducers with a fixed pattern. The HullSonic controller is microprocessor-driven: it drives every channel continuously and keeps retuning each one to its section of hull, so the energy goes where it works.

Is it certified?

Yes. The systems are certified FCC, CE and RCM.

What warranty do I get?

Three years return-to-base on every system, extended for as long as you keep a HullSonic dashboard plan active.

What happened to CleanAHull?

CleanAHull is now HullSonic MAX: the same team and engineering under one brand. CleanAHull warranties are honoured on their original terms, and if you bought from cleanahull.com, your orders are in your HullSonic account. u003ca href=u0022/cleanahull/u0022u003eWhat changedu003c/au003e.

Do prices include tax and import duty?

Yes, wherever we deliver duty paid. In Australia prices include GST. For New Zealand, the UK, the EU, the USA and Canada, the price you see includes the import VAT or GST and any duty for your country: we pay them to customs on your behalf, so there is nothing to pay on delivery, and your receipt shows the amounts. In Canada, HST replaces GST at checkout for Ontario and the Atlantic provinces. For other destinations, import charges are payable on delivery.

Still deciding?

Ask us, or see it on your own boat

If your question is not answered here, the team that builds the systems will answer it. If you would rather see how it fits, the layout planner draws it for your boat.

Plan my layout